How to Brush Skis and Snowboards for Better Speed
Share
A good wax deserves a proper finish. Scraping removes the bulk of the wax, but brushes reach the small grooves a scraper passes over. Use the right brush before waxing to clean the base, then work through the finishing brushes after scraping to expose the structure and improve glide.
Here's a brief rundown of what different brushes are for, and how to use them the right way to transform you base(s) and gain faster speeds every time you hit the slopes.
Whether you're a racer or all-mountain cruiser, these details are vital to up your glide, without changing your wax:
Why brushing matters for speed?
Your base has a fine pattern called structure. It helps manage the thin water film at the snow–base interface and reduce drag. Wax residue lodged in that pattern can interfere with its job. Brushing clears the existing grooves; it does not replace a stone grind or create a new structure.
This guide covers hot-waxed alpine skis and snowboards using brass, nylon and horsehair brushes.
(Liquid, paste and specialty race products may require a different finishing routine. Follow their application instructions.)

A scraper clears the surface; brush bristles reach residual wax in the structure. Illustration is for demonstrative purposes.
The three brushes and their jobs
Brush: |
Role in the brushing system: |
When to use it: |
|
Brass — coarse / stiff |
Loosens dirt and old wax; helps clear very hard wax |
Before waxing; optionally after scraping hard cold wax |
|
Nylon — medium / workhorse |
Removes remaining wax efficiently |
After scraping, before horsehair |
|
Horsehair — fine finish |
Lifts finer residue from the exposed structure |
After nylon |
These are functional descriptions, not standardized grit grades.
Bristle diameter, length and density affect how a brush behaves. Racewax recommends nylon before horsehair; some other systems finish with a fine nylon brush.
Follow the sequence for the actual brushes you own. As a rule of thumb: Always start with the coarsest brush first, and move to finer brushes as you polish.

Brushing before waxing with hand brushes
1. Get the base ready
Bring the gear indoors, let it reach room temperature and dry it. Secure it base-up in a suitable vise or support, and hold ski brakes clear. Remove loose grit before working it into the surface. Complete edge work and clear away metal filings before waxing.
2. Clean with brass
For Racewax brass preparation, work tail to tip. Start with three controlled full-length passes, then inspect. Hold the brush flat enough for the bristle field to contact the base evenly. Use enough pressure to lift residue without gouging or flattening the bristles. Wipe away loosened debris with a clean, lint-free cloth.
Keep a brush reserved for dirty preparation whenever possible. Label it so it is not confused with a clean finishing brush. The point is to remove contamination before applying fresh wax, rather than carry it into the next coat.
3. Deal with stubborn contamination
If the base still carries oily spring grime, brushing alone may be insufficient. Use a cleaner intended for glide bases, following its brushing, wiping and drying instructions. Allow it to dry fully before hot waxing. A brush used with cleaner should be kept separate from finishing brushes.
A compatible soft-wax hot scrape is another cleaning method: apply it, scrape while warm to lift contamination, then apply the wax you intend to ski on. This cleaning step has a different timing from the cooled scrape used for a final hot-wax finish.
Brushing after waxing with hand brushes
1. Let the wax cool and scrape first
For a typical hot wax, cool at room temperature; Racewax suggests roughly 30–60 minutes. Follow the wax maker’s instructions for hard waxes that require earlier scraping. Use a sharp plastic scraper to remove the excess, including wax caught along the edges. Brushes should clear residue, not chew through a thick wax coating.
2. Use brass only when needed
For very hard cold-weather wax, a clean brass brush can help release stubborn residue before nylon. It is optional for ordinary softer waxes. A dirty prep brush should not become your finishing brush.
3. Clear the structure with nylon
Work tip to tail in controlled, overlapping passes. Lift the brush for the return rather than scrubbing repeatedly in both directions. Keep its bristles working evenly across the base. On a snowboard, use several lengthwise lanes so both edges and the center receive attention.
Use five to ten passes as an initial check, not a fixed finish line. Wipe away the loose dust and inspect. If more residue is lifting, continue with measured passes rather than pressing harder.
4. Finish with horsehair
Follow with the finer horsehair brush, again tip to tail. Its job is to reach the fine structure exposed by nylon. Check under light from a low angle: the pattern should be visible, with no obvious wax ridges and very little fresh dust coming up. Judge the result rather than chasing a mirror shine.

Brushing preparation runs tail to tip. After scraping, finish tip to tail with nylon, then horsehair. Overlap passes to cover the full base.

Using roto brushes before and after waxing
Roto brushes are cylindrical brushes driven by a drill through a shaft and handle. They speed up the same preparation and finishing tasks, particularly across several pairs of skis. Hand brushes can still produce a thorough finish; rotary brushing mainly reduces repetitive work.
Set up for control
Use a compatible shaft, handle and protective shield, and secure the gear. Select a brush width suited to your ski or snowboard. With power disconnected or the battery removed, fit the brush and check that the axle is fully seated before use. Hold the drill and handle securely, keeping loose clothing and hair clear.
Wear safety glasses, use ventilation and dust extraction where available, and use suitable respiratory protection for wax dust. Direct debris away from your face. Brushing creates airborne particles even when the wax is fluoro-free.
Before waxing use brass for cleaning
Use the Racewax brass roto brush with light pressure, travelling tail to tip for preparation. Keep the axle across the base and move continuously along its length. Wipe away the loosened residue before applying wax. Use a dedicated cleaning brush, especially on dirty bases.
After waxing scrape then finish
Cool and scrape as for hand brushing. If needed, use clean brass for very hard wax; otherwise start with nylon, then change to horsehair. For finishing, travel tip to tail and set the rotation so the bristles at the contact point sweep wax toward the tail. Keep the shield positioned to deflect debris away from you.
Maintain light contact and an even travelling pace. Stop the drill before changing brushes. Repeat only while residue is lifting. Do not park a spinning brush on one spot or push down to compensate for inadequate scraping.
Racewax roto brush |
Published speed guidance |
|
Brass |
About 800 rpm |
|
Nylon |
Do not exceed 1,200 rpm |
|
Horsehair |
Do not exceed 1,200 rpm |
These figures apply to the Racewax brushes covered here. Use your exact model’s instructions if they differ. Excess speed or pressure can generate heat, smear wax and damage bristles.

For post-wax finishing, both travel and the bristle sweep at contact point run toward the tail. Pre-wax Racewax brass travel runs tail to tip.
Keep the finish and the brushes clean
Remove loose wax from your brushes regularly and store them clean and dry. Keep dirty prep brushes separate from clean finishing brushes. Avoid using compressed air to blow wax dust around your workspace. Check worn or distorted bristles before the next tune.
If wax smears, let the base cool and reduce pressure or speed.
If heavy shavings keep coming up, revisit the scraper. If the structure is clear and little dust appears, stop. More brushing is useful only while it improves the finish.
Summer Storage Wax
For seasonal storage, leave the protective wax coat on the base. Scrape and brush when you are preparing the gear for snow again.
Choose the brush for the job, cover the whole base and let the bristles do the work. That final attention to the structure helps your wax deliver the glide you prepared it for.
Hopefully this blog, The Art of Speed: Brushing helped you learn something new that you can apply to your tuning routine. Different wax isn't necessarily the key to faster speeds.
So try out this brushing process next time you wax.
You'll feel the difference. Thank us later.
Explore hand brushes and roto brushes at Racewax Brushes ->